Is your sink giving you trouble with water stains or a faded appearance? Reglazing could be your ultimate solution. Maybe it’s the first time you hear about reglazing and wonder what it is all about. The glaze is the finish that’s found in ceramic sinks. Reglazing involves putting another layer of glaze to give the sink a glossy look if it’s faded or cracked.
Glazing is always a better option compared to replacing your sink that’s worn away. Another advantage of reglazing is that you can try out a different color for your sink without purchasing a new one. Well, reglazing will only bear satisfactory results if done the right way. This article brings several tips to ensure that you reglaze your sink the right way to obtain your desired brand new look.
Essentials for Reglazing
First, it’s essential to have a list of all the items you will require for reglazing as listed below.
- Pipe wrench
- Abrasive powder cleanser
- Scrubbing pad
- Large sponge
- Painter’s tape
- Plastic sheeting drop cloth
- Clean cloths
- Putty knife
- Hard-water deposit remover
- Wet-dry 400- to 600-grit sandpaper
- Tack cloth
- Wooden stirring stick
- Paint roller or high-quality varnish paintbrush
- Epoxy refinishing kit
- Paint tray
- Rubbing alcohol
- Rubber gloves
- N95 face mask or respirator
Preparing to Reglaze
You are not in the business to reglaze your entire kitchen countertop. Hence, you will need to take preparation measures to ensure that you reglaze the only area you intend to.
First, you will need to take off the faucet and put it aside. Moreover, you will need to purchase some tape or plastic to cover the area around the sink to avoid glaze splash.
Don’t forget to put on an N95 face mask to protect you from the glaze fumes.
Clean the Sink
The number one step to reglazing your sink is cleaning it up first to remove stains. Removing stubborn stains from your ceramic sink may not be a walk in the park; hence you will need some abrasives to scrape them off. If you come across one stubborn stain, the elbow grease will come in handy in managing to get rid of it.
This is an essential step in the reglazing process as you don’t want to reglaze on existing stains.
Sand the Sink
Before starting with the reglazing process, you will need to sand the sink. You are wondering why sanding will be necessary. To get perfect glazing results, you will need a rough surface, and that’s where sanding comes in. The harsher the surface gets, the more the glaze will stick properly.
Also, remember to sand small circles to ensure that you attend to every bit of the sink. Once you are done with sanding, you can wipe the sink with a damp free cloth to ensure that no dust is left in the sink.
Reglazing the Sink
Once you are done with cleaning and sanding, it’s now time to apply the glaze. First of all, don’t forget to open the windows to keep the room adequately ventilated before you begin glazing. This is because paint products can easily cause suffocation in areas that are not sufficiently ventilated.
You can use a paint roller or a sponge to apply the glaze. Usually, you will need to start with epoxy glaze, followed by the acrylic coat. Before applying the acrylic coat, you need to ensure to give the epoxy glaze at least an hour to dry. The applying process should be repeated three times while leaving the coat to dry up at each interval.
Once you are done with glazing, you can now reattach faucets and uncover the protected region. It is important to note that you shouldn’t forget to read warnings from the epoxy product manufacturer to ensure that you mix it up appropriately.
For the best of results, you can consider applying an epoxy that complements your kitchen accessories.
The formation of streaks on the glazed sink will hinder you from getting the beautiful results of reglazing. To avoid this, you will need to be careful not to leave the long streaks on the primer. This can be done by using a short nap roller instead of a paintbrush. If you have to use a paintbrush, you must be careful to smoothen out all the pain marks in the sink.
There is also a second option of applying spray-on primers to ensure that no marks are left unattended.
Leave the glaze to Dry
Whether it’s done by a professional or you do it your own, you will need to give the glaze some time to dry up. This means you will need to get an alternative for the sink since you will not be using it for at least a few days.
Precisely, you will need to wait for each primer coat to dry up as instructed by the manufacturer. Importantly, turn the water to your sink before you start glazing as someone might mistakenly turn it on before the primer dries up and ruins all your hard work.
Also, you will need to avoid using strong abrasives on a newly glazed sink to avoid tampering with the finish. Furthermore, you can get a wire grate or a mat for the sink bottom to keep it protected from scratches from pots and other kitchen utensils.
If you wonder if reglazing will make any difference on your sinks, try out the above guidelines and be utterly surprised. With these guidelines, you will be able to bring your seemingly dead kitchen sink back to life. Importantly, you can also get your sink some new fittings to give it a brand new look!
Finally, you can do reglazing yourself without looking for a professional. However, getting a professional would be a great option since they are more experienced in the job and likely to deliver the best results for the job. Some more good news is that reglazing is quite pocket-friendly, and you won’t need to break the bank to cover the expenses involved.